Replacement Parts for the "PRONGHORN" and the "GOAT"
Throttle and Brake Parts
The Dual Brake Lever provides a means to connect the front and back brake to one lever. The engagement point can be adjusted separately. Not for hydraulic brakes.
The replacement throttle cable is custom made to replace both models.
The replacement throttle lever is a specifically designed lever that allows the user to quickly remove and connect the Weller Push Trailer throttle.
This remote throttle parts kit is designed specifically for the Harbor Freight 79cc Engine. The kit includes all parts necessary to connect the throttle cable to the engine. As a bonus you will also receive the correct drill bit. Complete instructions, via a video, is located on the Assembly page of this site.
The replacement throttle cable stop is used to adjust the throttle cable length on the engine side.
Frame and Engine Parts
The Replacement Wheel Axle Bolt Assembly is cut to the proper length for both the "Pronghorn" and "Goat" models. The assembly includes the appropriate washer and lock nut.
The Frame End Caps can be used on both models. (4 Each)
Frame End Caps. (1 Each)
The Optional Gun Rack Bar is custom built to allow the owner to carry their gun and other supplies on the Weller Push Trailer.
Warning, all guns/weapons must be unloaded and checked for safe transport.
Replacement Rack Post. The Rack Post is specifically built to allow a seat post rack to be installed on the Weller Push Trailer. All hardware included.
This is a complete Roller Assembly for the "Pronghorn". Includes all hardware and high quality bearings.
Replacement High Quality Roller Bearings for the "Pronghorn".
(2 each)
Replacement Bushing for the Yoke Assembly. Fits both "Goat" and "Pronghorn" models. (1 Each)
Replacement High Quality Jack-shaft Collar for the "Goat" model. (1 Each)
Replacement Sealed High Quality Jack-shaft Bearing for the "Goat"
(One Each) *Requires two bearings for Jack-Shaft assembly.
Replacement Sealed High Quality Wheel Bearings for all models.
(One Each) *Requires two bearings for the wheel assembly.
Replacement Jack-shaft sprocket, 22 tooth. To get the maximum torque out of your "Goat", this is the one for you. The replacement sprocket and set screws are included. Please use your original key to secure it to the Jack-shaft.
Replacement Jack-shaft sprocket, 21 tooth. Excellent for climbing in moderately steep hills with light loads. This is the all around best performer for trail riding.
Replacement Jack-shaft sprocket, 18 tooth. Provides good overall speed but not designed to climb steep hills. This would be for those that live in rolling hills. A little more speed with a sacrifice in overall hill climbing ability.
The Upgraded clutch provides the owner with the the best clutch on the market. This is a direct replacement for the standard clutch. 5/8" shaft. If you are replacing the standard clutch, you must order the replacement shaft bolt for Hilliard Extreme Duty Clutch found on this page.
Standard Duty Clutch 5/8" shaft. Although this is the standard duty clutch, it performs well and is quieter than the Heavy Duty version. If you are replacing the Hilliard Extreme Duty Clutch for the standard clutch, you must order the replacement shaft bolt assembly for the Standard clutch. It can be found on this page.
Standard Duty Clutch 5/8" shaft. Although this is the standard duty clutch, it performs well and is quieter than the Heavy Duty version. If you are replacing the Hilliard Extreme Duty Clutch for the standard clutch, you must order the replacement shaft bolt assembly for the Standard clutch. It can be found on this page.
Replacement Shaft Bolt with correct shim for the 79cc Harbor Freight Engine. This fits the Standard Clutch Only!
Replacement Shaft Bolt for Hilliard Extreme Duty Clutch. Will only fit Hilliard Clutch.
Replacement Chains and Parts
Full Set of Chains with Master Links for the "GOAT" model. This includes both chains and links. See Helpful Tips for proper chain maintenance.
GOAT MODEL ONLY.
Rear Chain only for the "GOAT" Model. Cut to length including the Master Link. GOAT MODEL ONLY
Front Chain with Master Link. Cut to length.
Goat Model Only
Replacement Chain and Master Link. Cut to length.
For the "Pronghorn" model only
Replacement Half Link for rear chain.
"GOAT" Model Only
Replacement Master Link for #40 and #41 chain. Check on the side of your chain to determine the proper number.
